Separate First Letter back panel and shorter A little hello pocket front with an envelope illustration and three hatched glue tabs: full Letter PDF preview — Printable sheet · Letter preview · A4 available

First Letter / FL03

First Letter Pocket with a Separate Back

Free printable PDF · A4 & Letter · No sign-up

Keep a small paper exchange together behind an open-top pocket. This sheet includes both the tall First Letter back and the illustrated A little hello front.

1 printable sheet
1 back + 1 front with glue tabs

94 × 115 mm
Finished outer size

Get this sheet

Paper size

Letter 8.5 × 11 inA4 210 × 297 mm

1 sheet · Color PDF · Choose your paper size

Choose paper size

Open PDF Printing help

Print at 100% / Actual size. Single-sided.

For personal journals and handmade gifts. No resale or redistribution. Use & credits.

Report a file issue

Direct paper-size downloads

Choose the paper loaded in your printer. These links also work if page scripts cannot load.

Download A4 PDF · 1 page · 335 KB Download Letter PDF · 1 page · 335 KB

Two ways to use this sheet

Follow the first-letter project

MFL combines this pocket with FL01 and FL02. Arrange the paper pieces before gluing, leaving room above the pocket to reach the notes.

Keep one short reply

Use a loose card to hold a reply or a small introduction. Try one layer first; this flat pocket has no expanding gusset and is not a promise of multi-card capacity.

Glue the tabs to the back

Cut both separate pieces. Fold the three tabs behind the front and glue them to the marked area on the printed back. Leave the top open. The nominal glue-free width is 82 mm; usable space still depends on folding, glue and paper thickness.

What’s on this sheet

Individual previews below are not shown to scale. Use the printed dimensions to compare pieces.

View detail ↗
First Letter back panel
A 94 × 115 mm backing piece with a marked area for attaching the separate front. It remains visible above the opening.
94 × 115 mm
Finished outer size · FL03-a
View detail ↗
A little hello pocket front
A 94 × 75 mm front face with three 6 mm glue tabs. Its full flat outline is 106 × 81 mm; the tabs must remain attached when cutting.
94 × 75 mm
Finished outer size · FL03-b

Digital candidate r0.10. Printing, paper thickness and assembly fit still need physical checks.

Fold and fit notes

Cut solid outlines, fold dashed lines and apply glue only to hatched GLUE areas. Keep the opening clear. Check the 50 mm ruler before cutting.

This sheet includes a separate 94 × 115 mm back and a 94 × 75 mm front with three 6 mm glue tabs. The nominal glue-free width is 82 mm. Fold the tabs behind the front, then attach it to the printed back. Keep the top open.

Target card compatibility is a test plan, not a verified fit claim.

Help with this file →

A closer look

Enlarge this detail ↗

Inspect the actual first letter pocket at readable size.

Detail · Cropped from the actual PDF. The full page above shows every component.

Make a journal page with this sheet

A first-letter keepsake · 3 sheets, piece map and illustrated steps

Use it with

Choosing and using this printable

Is this an envelope?

No. It is an open-top pocket with no closing flap. The download includes its back and front, but no separate note or envelope.

Are FL01 and FL02 proven to fit together inside?

They are intended project companions, not a verified loaded-capacity claim. FL01 adds a fold and extra paper thickness. Actual insertion, removal and capacity need a physical trial.

File notes

AI-assisted illustrations; text, linework and millimetre layout are controlled separately. The previews are rendered from the PDF.

Revision r0.10: Separate back and front widened to 94 mm; 6 mm tabs retained. Nominal glue-free channel 82 mm for a 78 mm card. Original raster artwork unchanged; physical fit untested. Physical evidence is still pending for this revision.

Use, sources and credits →